2011 TE 310 off idle HESITATION

Discussion in 'EFI/carb' started by Havago, Jan 16, 2011.

  1. Havago Husqvarna
    B Class

    I have a 2011 TE310 which has a very bad just off idle hesitation which make it easy to stall depending on the track situation. Runs fine once past it in higher RPM.

    It seams to be the same problem on the 2010 TE250

    Can anyone provide a solution or specific ibeat settings?

    I mainly ride tight rocky single track, 1st and 2nd gear stuff. This my first Husky and FI bike, not such a good start.

    Thanks for any help
  2. 1650bullet Husqvarna
    AA Class

    I live in brisbane Qld (Just up the road a bit) First of all who did you buy your bike from, and did they set it up on the ecu properly. Its a very simple fix that you need to do. The ECU needs to be reflashed and have the tps and co levels adjusted. Because the bike is a 2011 model you should be able to take it to a husky dealer and have it done under warranty. If its not covered it should only set you back $50 to $80 dollars, Full throttle motorcycles at slacks creek is the best to take your bike to, They know there stuff. Ask for stefan at the parts counter and tell him of your problem and he will put you on the wright path, 07-32091977
  3. raisrx251 Husqvarna
    AA Class

    Location:
    Virginia
    The best thing for you to do is contact your dealer and importer. Do not accept anything but satisfaction on this. It may not be similar to the 2010's situation, at least I hope not!

    Does it hesitate on both maps?
  4. raisrx251 Husqvarna
    AA Class

    Location:
    Virginia
    Oops, 1650, are you saying that the 2011 310's are being re-flashed like the 2010 250's were?
  5. Havago Husqvarna
    B Class

    Thanks for the quick replies,

    Yes, it does hesitate on both maps,

    I have taken it back to the dealer and Iwill let you know what he has done.
  6. husky bom Husqvarna
    A Class

    yes i rode a new 310 and it had the off idle bog the same as the 2010 te 250's ..... all it needs is the efi to be remaped and this can be done at your dealer... i would take it to full throttle thay are the best up your way other wise you will get the basic map and its shit thats why you have problems ......and gearing is a problem on the 310 as well it needs a 12 on the front for single track 12/50 seems to work well thats what we did down hear on the one we set up and is great

    good luck
    H.B
  7. Havago Husqvarna
    B Class

    Thanks for advice Husky Bom, I was going to try a 52 on the back but I will try a 12 on the front which will be easier.
  8. whiskeythrottle Husqvarna
    AA Class

    Location:
    Kamloops BC Canada
    I own a 2011 te 310 and I have no bog whatsoever on either map.
    I Have my bike derestricted, following factory procedures and it works flawlessly.
    I ran my bike on the dyno and found the factory settings were pretty much bang on and I needed not change any mapping.
    I am unaware of any factory recomended ecm reprogramming.
    One thing that must be followed correctly is the derestriction process. It has to be all or nothing
  9. Coffee CH Owner

    Location:
    Between homes - in ft Wayne IN
    Husqvarna Motorcycle:
    2006 TE250, 2013 TR650 Terra - sold
    Good input whiskeythrottle, I've heard nothing as well. My impression so far is that the efi was sorted out for 2011.
  10. Klas Husqvarna
    A Class

    Location:
    Sweden
    Hi guys

    My advice, change tempsensor. There is big problems with that. som sensor have a slight differnce in value compared to real temp of the engine. when he diagnostic tools in conected it sems right. But still a small diff to the engine temp. And that give a poor trottleresponse.
    Some are complete broken. On a new bike it is importent to put some grease on the contactpins. To protect it from water etc.

    We have changed a lot of them on bikes here in Sweden. Poor quality. We have recived a new type here in Sweden.

    Klas
  11. herpindo Husqvarna
    A Class

    Location:
    Bali
    Klas,
    Same here the sensors are really bad on the 2010 TE250 as well, how do you find the new ones??

  12. Klas Husqvarna
    A Class

    Location:
    Sweden
    Hello

    The conector socket is white plastic instead of black. TE 449 use it. I think Suzuki RMZ 450 use the same sensor.

    But it is still importent to put som grease on the conecting pins and sealing surface. We have done this on new bikes with good results.

    Klas