BRP Handlebar clamps/ handguard mounts

I was sick of clamping more stuff to my bars with them getting more and more cluttered. I put on a set of the BRP bar clamp/ handguard mounts. WOW! want a great product. It works way better and looks super pro. My bike is almost perfect, I may need to sell it soon.

Well, what bike would that be? And please, post a photo of how grand it is.

Photos Please !!

SAM511

I am not a fan of triple clamp mounting.
SAM511

http://www.brpmoto.com/products?pag...page.pbv.tpl&product_id=2174&category_id=1528

This is what I got, I'm out of town so I can't send any pics till sunday, sorry.

Look forward to pics from a few angles.
SAM511

Kelly,
I guess its the fear of the unknown.
I just feel that I would not want to stress the top triple clamp in a hard fall. Don't know really.
On another note I am impressed with your setup on the TE511.
I am actually going to look into that setup.
Could you post a couple of shots from different angles for me ?
SAM511

Those work very well- I had the same set up on my ktm in the "BONZ" variety. They look great, cleaned up the bars, and added alot of stability to the guards. I would have swapped them to my Husky when I sold it, but they did not fit (though,could have swapped lower bar mount). I then got the Cyrca CRM for the Husk, which though not the same accomplishes the same just not quite as cleanly.

I finally got pics up, this work thing is really getting in the way of things of late.

Ordered some and recived today leaving for race tomarrow. Holes are too close together to fit on the handlebar clamp, now I'm scewed for the race.

I figured it out... wait for it.........
Suamico Sd Must have swapped his lower handelbar clamps... maybe he swapped out the stock ones prior to the BRP's.. Cause I went back and looked at BRP's site: they sell only ONE part for all bikes but list them for all bikes specifically like a 09TE450- so if you select your specific bike you'd think all the parts listed will fit. And with Suamico SD having them - I assumed they'd fit (unlike my BONZ)... But BRP states they fit all 39-41mm spacing- so BRPs fit KTM's (look at the spacing on my old KTM and Suamico Sd's Husky- looks about the same...) I measured MY Stock handelbar clamps on my 09TE450 andy they are about 50mm center to center...

SORRY Benriding They won't fit! http://www.brpmoto.com/products?pag...page.pbv.tpl&product_id=2174&category_id=1552
You'd have to get lower handelbar mounts that would be compatible with your bike and the BRP's....

You can take parts off my bike for the race- hopefully my stuff will fit
Return the BRP's and get a set of Enduro Engineering or Cyrca CRM's- , just stop by Halls and get a set on the way to the race, they have handelbar clamps too if you wanted to convert for the BRPS.,. call tomorrow, tell them your issue, and have them set aside all the right stuff for ya
https://www.halls-cycles.com/Catalog/Halls-Cycles-Husqvarna-Protection.aspx
https://www.halls-cycles.com/Catalog/Halls-Cycles-Husqvarna-Clamps.aspx

or use mine, either way stop out and burn in my trail in the am

Sorry if i caused confusion. The lower bar clamps were on the bike when i purchased it. I assumed they were stock. I guess not.

Called BRP and they actually machined some lower bar clamps to fit my bike, awsome cust.service I had a problem and they worked with me to fix it!

Gotta love guys like that. I got almost the same treatment today from Rekluse. Great guys!

It's probably not any more stress on the top triple than you get when you bang your bars the ground in a hard fall. That force still transfers to the bar clamp.

On my TE 310 only one bolt on top triple so if by chance force was put on it, would snap and race is over.

Suamico SD isn't by chance JD is it?