1. 2 Stroke Husqvarna Motorcycles Made In Italy - About 1989 to 2014
    WR = 2st Enduro & CR = 2st Cross

250-500cc LOWER TRIPLE CLAMP

Discussion in '2 Stroke' started by 454x, Jan 23, 2013.

  1. 454x Husqvarna
    Pro Class

    Location:
    Dunnigan,Ca.
    Husqvarna Motorcycle:
    2012 CR165 w/36mm lectron.
    Other Motorcycles:
    2014 BETA 300RR w/36mm lectron.
    Has anyone had a problem with they're lower triple clamp steering stop sheering off on either the left or right side? When I bought my bike it was sheered off so, I bought a whole new lower and low and behold it has sheered off again like a hot knife through butter.
  2. juicypips Husqvarna
    Pro Class

    Location:
    gloucestershire
    Husqvarna Motorcycle:
    wr 360. 2002
    Other Motorcycles:
    Gas Gas TxT 300, Yamaha wr250f
    where it hits the frame? did you sling it up the track?
    wich bike is it? could you weld another stop back on it?
  3. pvduke Husqvarna
    Pro Class

    Location:
    ... on the gas...
    Husqvarna Motorcycle:
    tripple-hondo hoosk...
    Other Motorcycles:
    dozens of them, kicked to the curb
    ya mean the bump stop on the clamp or, pic maybe?? my welder does wonders with triple-clamps. ill give ya his number in case yer interested.
  4. 454x Husqvarna
    Pro Class

    Location:
    Dunnigan,Ca.
    Husqvarna Motorcycle:
    2012 CR165 w/36mm lectron.
    Other Motorcycles:
    2014 BETA 300RR w/36mm lectron.
    Yes the bump stop on the bottom clamp has sheered off.
  5. chris anders Husqvarna
    AA Class

    Husqvarna Motorcycle:
    2002 CR250 , 2002 CR125
    Other Motorcycles:
    2003 Suzuki RM250
    Yep, mine too-02 cr250. sliced that sucker right off!
  6. ohmygewd Husqvarna
    Pro Class

    Location:
    Melbourne, Australia
    Husqvarna Motorcycle:
    13'Berg FE350, 96'WR360, 01 WR250
    Other Motorcycles:
    Aprilia RSV1000
    Common issue since adam was a boy, the issue is the sharp and hardness of the metal that strikes the stoppers which rounding off the hard edge helps prevent but won't stop this from occurring. Grind flat the sheered off stopper then you can either drill and place a rubber or hard nylon bump stop or have it aluminum weld a new stop.

    Some guys have a welded a bar on the frame with nylon ends that hits the lower clamp base and it seems to work better than the bump stop.
    juicypips likes this.
  7. 454x Husqvarna
    Pro Class

    Location:
    Dunnigan,Ca.
    Husqvarna Motorcycle:
    2012 CR165 w/36mm lectron.
    Other Motorcycles:
    2014 BETA 300RR w/36mm lectron.
    Similar to how the cr 125 is????
  8. ohmygewd Husqvarna
    Pro Class

    Location:
    Melbourne, Australia
    Husqvarna Motorcycle:
    13'Berg FE350, 96'WR360, 01 WR250
    Other Motorcycles:
    Aprilia RSV1000
    Yep, the same design all the way through the range (and with other make's as well). The welded bar stopper on the frame was OE on my old KDX (better design).

    Should say, that design is the same from 1990's (maybe 80's) onwards......and same issue.

    PS..Stop falling and you wont have to replace them:p
    juicypips likes this.