1. 2 Stroke Husqvarna Motorcycles Made In Italy - About 1989 to 2014
     WR = 2st Enduro & CR = 2st Cross

250-500cc wxc 250 front sprocket - have a pic or measurements?

Discussion in '2 Stroke' started by dhallilama, May 30, 2015.

  1. dhallilama Husqvarna
    A Class

    Husqvarna Motorcycle:
    '96 WXC 250
    Other Motorcycles:
    many. i'm addicted.
    '96 WXC 250... does the sprocket have any offset, or is it flat?

    i misplaced (or tossed) the front sprocket from mine when tearing the bike down (it was missing a couple teeth). walking in my garage today, i saw a stack of sprockets for my Yamaha IT250... turns out the splines fit nicely on the Husky's shaft.
    i haven't checked chain alignment yet... it'd be sweet if the alignment is good as i've got a bunch of these sprockets from 12t through 18t


    [IMG]
    dhallilama, May 30, 2015
    #1

  2. Big Timmy Husqvarna
    Pro Class

    Location:
    (South Eastern) AZ.
    Husqvarna Motorcycle:
    2015 FE 501 with lots of goodies.
    Other Motorcycles:
    BMW G450X, 15'FE501, 23 KTM 1290 SAR
    Just look it up on the JT Website. This was the listing for the Husky 96 250s
    It didn't have a listing directly for the 96 WXC 250


    [IMG]
    Husqvarna 250 CR — USA

    Off Road

    1995 to 1997
    Front Sprocket
    Part No. Teeth
    JTF507 13
    Available Sizes
    13, 14, 15
    [IMG]
    Rear Sprocket
    Part No. Teeth
    JTR822 48
    Available Sizes
    41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51, 52, 53
    [IMG]
    Big Timmy, May 30, 2015
    #2
    dhallilama likes this.

  3. dhallilama Husqvarna
    A Class

    Husqvarna Motorcycle:
    '96 WXC 250
    Other Motorcycles:
    many. i'm addicted.
    well hole-e-chit.... I didn't even think of that. thank you!

    oh well, looks like these won't work. on the plus side, sprockets are cheap anyway...
    dhallilama, May 30, 2015
    #3

  4. Big Timmy Husqvarna
    Pro Class

    Location:
    (South Eastern) AZ.
    Husqvarna Motorcycle:
    2015 FE 501 with lots of goodies.
    Other Motorcycles:
    BMW G450X, 15'FE501, 23 KTM 1290 SAR
    Yes your right, the JTF569 sprocket is flat on the engine side anyway that you have pictured. This would affect the alignment.

    Front Sprocket
    Part No. Teeth
    JTF569 13
    Available Sizes
    10, 11, 12, 13, 14, 15, 16, 17, 18
    [IMG]
    Big Timmy, May 30, 2015
    #4

  5. justintendo klotz super techniplate junkie

    Location:
    mercer, pa/northwest pa
    Husqvarna Motorcycle:
    84 250,86 400,87 430,88 250,95 360
    Other Motorcycles:
    99 kawasaki zrx 1100
    the jt are good stuff for the money. i always run their steel front and rear sprockets. the rears last a looong time...
    justintendo, May 30, 2015
    #5

  6. dhallilama Husqvarna
    A Class

    Husqvarna Motorcycle:
    '96 WXC 250
    Other Motorcycles:
    many. i'm addicted.
    offset is 3mm with the shoulder... enough to throw off the chain alignment.

    JT do make great sprockets... have their steel front/rear on all my bikes. lasts a lot longer than aluminum, that's for sure...
    dhallilama, May 30, 2015
    #6

  7. Big Timmy Husqvarna
    Pro Class

    Location:
    (South Eastern) AZ.
    Husqvarna Motorcycle:
    2015 FE 501 with lots of goodies.
    Other Motorcycles:
    BMW G450X, 15'FE501, 23 KTM 1290 SAR
    Recently picked up a 48 and a 49 rear for my FE 501 myself. For about what a single aluminum sprocket costs. I am already running the 48 on the rear now and the difference in weight, changing from the stock aluminum sprocket to the JT Steel sprocket is negligible.

    For what I do with the bike, It will last a hell of a lot longer as well.
    Big Timmy, May 30, 2015
    #7