• Hi everyone,

    As you all know, Coffee (Dean) passed away a couple of years ago. I am Dean's ex-wife's husband and happen to have spent my career in tech. Over the years, I occasionally helped Dean with various tech issues.

    When he passed, I worked with his kids to gather the necessary credentials to keep this site running. Since then (and for however long they worked with Coffee), Woodschick and Dirtdame have been maintaining the site and covering the costs. Without their hard work and financial support, CafeHusky would have been lost.

    Over the past couple of weeks, I’ve been working to migrate the site to a free cloud compute instance so that Woodschick and Dirtdame no longer have to fund it. At the same time, I’ve updated the site to a current version of XenForo (the discussion software it runs on). The previous version was outdated and no longer supported.

    Unfortunately, the new software version doesn’t support importing the old site’s styles, so for now, you’ll see the XenForo default style. This may change over time.

    Coffee didn’t document the work he did on the site, so I’ve been digging through the old setup to understand how everything was running. There may still be things I’ve missed. One known issue is that email functionality is not yet working on the new site, but I hope to resolve this over time.

    Thanks for your patience and support!

Pottering around...

Last job...a test-"sit" to check for clearance and "room-to-move" in the saddle + standing up.
While this particular bag is a touch too big for the Husky (just by proportions), it all fits like a glove and even looks like it was designed for it in the first place.


Husky_139.JPG



Check....lock-to-lock clearance.
No killswitch touching the bag, hurray!




Husky_140.JPG



Ergos? Fine...nothing in the way sitting or standing


Husky_141.JPG




An old "City" model bag that's given up the ghost years ago, provides a spare "bag"-mechanism, the top half of the "click 'n go" tankbag principle.
If/ when I come across a neat, small bag of any brand/ construction, I can use a thin piece of plastic sheeting as a floor stiffener, then bolt the spare bag-ring to it to make it a "Quicklock" bag.
AFAIK, SW has now decided to sell those rings separately as well, making it possible to convert most tankbags out there to the Quicklock system.



Husky_142.JPG


Well done

I used an Andy Strapz tank bag, I wrapped 50mm wide velcro around the seat, stapled so as not to move, then one clip bolted to the Safari x-brace, the bag clips to this & the velcro holds it in place - at petrol stops, just lift it off the velco
Or, fill the left-hand safari tank which slowly fills the other 2 tanks
9-10 litres per fill gives me about 250 klms
 
A random thread about a little garage in Oz...and some ideas about farkling a Strada (yeah...just because it was one of the last TR's availablle and there weren't any Terras left, shrug).

Bought the bike to put on the blocks for the first 6months or so of its life, fiddle and farkle, get a feel and an idea of how it's put together, and make up some bits I reckon I'll need for my riding lateron.
It'll transform to a 21" front (when/ if I ever come across a suitable BMW wheel)... I might keep the 17 rear, 'cause there's plenty of rubber of choice around for the riding I plan to do with it.
And I hate fixing tubed hoops!:mad: Especially rears!

I'll update the thread with thoughts and pics as the project rolls along.
There's still a long summer + autumn/fall ahead
A 21 front and 17 rear may be pushing the limits of the ABS system. Anyone tried it yet?
 
Nope...just checked the fit of the 21" BM-wheel in a Strada, that part's fine.
If needed, I'll turn the ABS off....never had it before, won't miss it.
 
I'm running a 21 front and 17 rear with my strada. No problem so far with abs.

Great to hear...all the base-parameters are BMW-derived anyway, and they've only ever used 21/17 combos, so there shouldn't be any problems... but one never knows.
 
There was 1 person that found his 21/17 setup to be so close to the edge of working that he had to make sure the tires were properly inflated. I don't recall the exact setup he used, but there definitely are some posts about it here.
 
There was 1 person that found his 21/17 setup to be so close to the edge of working that he had to make sure the tires were properly inflated. I don't recall the exact setup he used, but there definitely are some posts about it here.
The ABS Terra's are 21"/17" stock, I've never had any problems.
 
The ABS Terra's are 21"/17" stock, I've never had any problems.


Thanks.
There were also some dealer- "terra-fied" Stradas around near the end of the stock sellout here in Oz, as the Terras were selling significantly better than the Stradas.
Most went for the look only with the high front guard, but a few had the wheels swapped for Terra wire-wheels also.
Wonder, if they finished up with 17 or 18 rears.
The Euro ABS-Terras also had 17 rears, from memory.
I doubt very much that there've been different firmware versions for the ABS/ non-ABS and/ or the range of possible wheel-combos.
 
OK....some days you just get beaten. :-(

Dismantling was quick...just watch this connector (cut the cabletie + disconnect), as that's the one that can result in the dreaded EWS-error and a dead bike after playtime's over.

Husky_164.JPG


Pull the front 2 front clips holding the posts of the dash and check if you can pull the connector off the dash-socket (push the tongue down)....I couldn't, not enough space.


Husky_165.JPG



Husky_166.JPG



Had to drop the cross-brace to get to the 3rd post-clip in the back.


Husky_167.JPG


That's it


Husky_168.JPG




With the 8 Torx6 screws removed and the top cover off....the right of the 2 pins is the target.....or rather, the connecting "legs" of the switch underneath the pin.
In my case, the white plastic horizontal tab is still intact, preventing the removal of the pin.
And that means there's absolutely NO ACCESS to those 2 tiny 'legs" to attach the 2 wires to for an external switch.




Husky_169.JPG




Asking Greg/ DandyDisco which legs to attach the tap to, it's the 2 on the left (facing west...or...9 o' clock with the dash in the normal, natural position)


Husky_170.JPG



Outsmarted myself and pried the PCB out of the back-casing to solder or glue the wires to the bottom of the legs (as they usually stick through the PCB with the factory solder-points below securing the component/ switch in this case, to the board.)


Husky_172.JPG




All ready to roll and with some epoxy mixed up, I had another quick look at the 2 "tapping points" with a magnifying glass...and SHIT, those little "solderpoints" rather look like some sort of electronic component, some micro-resistor or capacitor or something !!
And I was seconds away from sticking a mighty epoxy-turd on top of each!

I'm beat!

Thankfully it all still works fine after an anxious re-assembly....3 hours blown, I'll have a beer now and think of some other goof-up I could fabricate :-))
Maybe some other day....when my S-button has packed up.
 
Rear sprocket carrier bearings...another potentially disastrous (as in ride-busting) issue on the TR

Unlike most other carriers, this one has TWO both bearings, side-by-side. with a small spacer in between.
Both bearings extract/ insert from one side only.

Sorry for the slightly blurred shot, but still clearly visible....double-depth bearing seat, showing the recess for the retainer clip.


Husky_173.JPG



Factory bearings are SKF Explorer 6204, 2 off...


Husky_174.JPG




...and a generic 30x40x7MM seal


Husky_175.JPG




The entire stack of bits and parts
Left-to-right as it belongs into the carrier:
1) Bearing at the bottom
2) retainer clip and spacer
3) the second bearing
4) seal


Husky_176.JPG



As the bearing seat is double-depth, I knocked the core out of one of the old SKF's, cutting and de-burring the outer to use as a tool
when carefully knocking in the new bearings.
Which should make for nice, smooth travel and seating of the new bearing without going askew along the way, possibly damaging the seat of the upper bearing.
The slot allows sufficient give to extract the ring after the first bearing's in place.




Husky_177.JPG
 
Sorry glitch. Didn't mention that it's a 7 layer circuit board and the switch is surface mounted.
What I did was use a very fine needle to make a gap between the leg coming from the switch and the switch housing.
Then insert a fine wire with a spot of super glue.

I can always drop by one night.

Cheers.
Greg
 
Sorry glitch. Didn't mention that it's a 7 layer circuit board and the switch is surface mounted.
What I did was use a very fine needle to make a gap between the leg coming from the switch and the switch housing.
Then insert a fine wire with a spot of super glue.

I can always drop by one night.

Cheers.
Greg


Hi mate

Would love to fix this before that plastic tongue on the button snaps...but it sounds like that has to happen (or made to happen)
as otherwise there's no access to the actual switch contacts to glue the tapping wires.
(is that about right?)
I'd also love to take some snaps of the fix to post up here.
 
Rear sprocket carrier bearings...another potentially disastrous (as in ride-busting) issue on the TR

Unlike most other carriers, this one has TWO both bearings, side-by-side. with a small spacer in between.
Both bearings extract/ insert from one side only.

Sorry for the slightly blurred shot, but still clearly visible....double-depth bearing seat, showing the recess for the retainer clip.


Husky_173.JPG



Factory bearings are SKF Explorer 6204, 2 off...


Husky_174.JPG




...and a generic 30x40x7MM seal


Husky_175.JPG




The entire stack of bits and parts
Left-to-right as it belongs into the carrier:
1) Bearing at the bottom
2) retainer clip and spacer
3) the second bearing
4) seal


Husky_176.JPG



As the bearing seat is double-depth, I knocked the core out of one of the old SKF's, cutting and de-burring the outer to use as a tool
when carefully knocking in the new bearings.
Which should make for nice, smooth travel and seating of the new bearing without going askew along the way, possibly damaging the seat of the upper bearing.
The slot allows sufficient give to extract the ring after the first bearing's in place.




Husky_177.JPG

Rear sprocket carrier bearings...another potentially disastrous (as in ride-busting) issue on the TR

Unlike most other carriers, this one has TWO both bearings, side-by-side. with a small spacer in between.
Both bearings extract/ insert from one side only.

Sorry for the slightly blurred shot, but still clearly visible....double-depth bearing seat, showing the recess for the retainer clip.


Husky_173.JPG



Factory bearings are SKF Explorer 6204, 2 off...


Husky_174.JPG




...and a generic 30x40x7MM seal


Husky_175.JPG




The entire stack of bits and parts
Left-to-right as it belongs into the carrier:
1) Bearing at the bottom
2) retainer clip and spacer
3) the second bearing
4) seal


Husky_176.JPG



As the bearing seat is double-depth, I knocked the core out of one of the old SKF's, cutting and de-burring the outer to use as a tool
when carefully knocking in the new bearings.
Which should make for nice, smooth travel and seating of the new bearing without going askew along the way, possibly damaging the seat of the upper bearing.
The slot allows sufficient give to extract the ring after the first bearing's in place.




Husky_177.JPG

When I did mine "just in case" used Niacini bearings from Japan - l removed the inner seal from each bearing then filled the space 50% with quality water resistant grease, this ensures adequate lubrication, virtually for ever
Also replaced the alloy spacers with stainless steel
 
When I did mine "just in case" used Niacini bearings from Japan - l removed the inner seal from each bearing then filled the space 50% with quality water resistant grease, this ensures adequate lubrication, virtually for ever
Also replaced the alloy spacers with stainless steel

Seems like a good idea...had them made locally?

Haven't come across "Niacini"-bearings, but never had a bad experience yet with the Nippon-made Nachi's. Or any Jap-made bearing for that matter.
 
Back
Top